• Load Assist (optional) Is designed to help shorten the learning curve of inexperienced operators to ensure consistency and faster loading of material while reducing effort of the operator. Based on the speed of the machine, Load Assist automatically adjusts the cutting edge height to manage wheel slip and to ensure consistent and efficient loading in bulk earthmoving applications.
• Machine Speed Limit is designed to take the place of top gear selection. If the machine top speed needs to be limited the operator can select the top speed through the display or the top speed can be set in ET. This will allow the machine to find the correct gear that works best for the engine and transmission. Allowing the engine and transmission to select the correct gear to pull the load in most cases resulting in a lower engine load factor and lower fuel burn verses using top gear selection that required the machine to run at engine speeds at or close high idle.
• Ground Speed Control sets the desired top speed by the operator if job site conditions or segment speed limits require a speed less than full run out. Machine Speed Limit is intended for use when top speed needs to be limited for longer durations and Ground Speed Control is intended for use when the top speed needs to be reduced for shorter segments or intermediate periods of time. The operator can set the desired top speed and the machine will find the correct gear that works best for the engine and transmission. Allowing the engine and transmission to select the correct gear to pull the load in most cases will result in a lower engine load factor and lower fuel burn verses top gear selection.

OPERATOR COMFORT AND CONTROL

• Ground Speed Control sets the desired top speed by the operator if job site conditions or segment speed limits require a speed less than full run out. Machine Speed Limit is intended for use when top speed needs to be limited for longer durations and Ground Speed Control is intended for use when the top speed needs to be reduced for shorter segments or intermediate periods of time. The operator can set the desired top speed and the machine will find the correct gear that works best for the engine and transmission. Allowing the engine and transmission to select the correct gear to pull the load in most cases will result in a lower engine load factor and lower fuel burn verses top gear selection.
• 615c Series steering system design requires significantly less steering effort. The reduced steering effort will allow for decreased operator fatigue and a more efficient operator resulting in possible higher rates of production late in the work cycle.

BUILT-IN SAFETY FEATURES

• Engine Over Speed Protection – In the event of an engine over speed situation, the compression brake or brakes will automatically engage with no operator input. The machine determines the over speed condition based on rate of acceleration and applies compression brakes automatically.
• The open bowls now come standard with bowl side overflow guards to help prevent material from flowing over the bowl sides and falling onto the draft arms where material becomes lodged between the bowl side and draft arm resulting in decreased work cycle times.
• Differential Lock Engagement Protection allows the machine to prevent the operator from engaging the differential lock when damage could occur.

SAVE ON MAINTENANCE TIME

• The filter bank located at the rear of the engine compartment has undergone improvements for serviceability by raising the filter bank up for easier access.
• In cold weather conditions the machine will use the Auto Stall feature to help warm up the transmission oil faster resulting in the machine shifting out of torque converter drive (2nd gear) faster than on previous models.

Caterpillar 615c scraper for sale

GENERAL

Top Speed – Loaded	33.5 mile/h
Number of Flights	15
Operating Weight – Empty	88061 lb
180° Curb-to-Curb Turning Width	38.71 ft
Overall Shipping Height	12.37 ft
Overall Length	45.18 ft
Maximum Depth of Spread	18.3 in
Fuel Tank Refill Capacity – Scraper	201 gal (US)
Scraper Capacity – Struck	18.8 yd³
Scraper Capacity – Heaped	23 yd³
Rated Load	25 038 kg (55,200 lb); 25.1 tonnes (27.6 tons)
Tires – Tractor Drive	33.25R29**E3
Width – Cut	10.3 ft
Elevator Flight Spacing	20 in
Overall Width	11.71 ft
Maximum Depth of Cut	10.3 in
Maximum Floor Opening	4.4 ft
Tires – Scraper	33.25R29**E3

ENGINE

Flywheel Power – Tractor/Scraper	304 kW (407 hp)
Rated Engine RPM	2000 r/min
Engine Model	Cat C13
Flywheel Power – Tractor	407 HP
Note	C13 engine emits equivalent to U.S. EPA Tier 2/EU Stage II or U.S. EPA Tier 3/EU Stage III.

TRANSMISSION

Top Speed – Loaded

33.5 mile/h

SCRAPER BOWL

Scraper Capacity – Heaped

23 yd³

SERVICE REFILL CAPACITIES

Fuel Tank	216.09 gal (US)
Crankcase	8.08 gal (US)
Cooling System	11.89 gal (US)
Hydraulic System	21.926 gal (US)
Transmission System	24.76 gal (US)

Caterpillar 615c scraper for sale